| SITOP MODULAR 48 V/20 A STABILIZED POWER SUPPLY INPUT: 400-500 V 3 AC OUTPUT: 48 V DC/20 A |
| Technical specifications | |
| Product | SITOP modular |
| Power supply, type | 48 V/20 A |
| Input | |
| Input | 3-phase AC |
| Rated voltage value Vin rated | 400 V…500 V |
| Voltage range | 320 V…550 V |
| Starting from Vin > 340 V |
| Wide-range input | Yes |
| Overvoltage resistance | 2.3 × Vin rated, 1.3 ms |
| Mains buffering at Iout rated, min. | 6 ms |
| Mains buffering | at Vin = 400 V |
| Rated line frequency | 50 Hz/60 Hz |
| Rated line range | 47 Hz...63 Hz |
| Input current / at nominal level of the input voltage 400 V | 2.2 A |
| Switch-on current limiting (+25 °C), max. | 70 A |
| I²t, max. | 2.8 A²·s |
| Built-in incoming fuse | none |
| Protection in the mains power input (IEC 898) | Required: 3-pole connected miniature circuit breaker 10 ... 16 A characteristic C o circuit breaker 3RV2011-1DA10 (setting 3 A) o 3RV2711-1DD10 (UL 489) |
| Output | |
| Output | controlled, isolated DC voltage |
| Rated voltage Vout DC | 48 V |
| Total tolerance, static ± | 3 % |
| Static mains compensation, approx. | 0.1 % |
| Static load balancing, approx. | 0.2 % |
| Residual ripple peak-peak, max. | 100 mV |
| Residual ripple peak-peak, typ. | 10 mV |
| Spikes peak-peak, max. (bandwidth: 20 MHz) | 200 mV |
| Spikes peak-peak, typ. (bandwidth: 20 MHz) | 80 mV |
| Adjustment range | 42 V…56 V |
| Product feature / output voltage adjustable | Yes |
| Output voltage setting | via potentiometer |
| max. 960 W |
| Status display | Green LED fo 48 V OK |
| Signaling | via signaling module (6EP1961-3BA10) |
| On/off behavio | No overshoot of Vout (soft start) |
| Startup delay, max. | 2.5 s |
| Voltage rise, typ. | 20 ms |
| Rated current value Iout rated | 20 A |
| Current range | 0 A…20 A |
| delivered active power / typ. | 960 W |
| constant overload current / at shot-circuit during run-up / typical | 23 A |
| shot-term overload current / at shot-circuit during operation / typical | 60 A |
| Duration of overloading ability fo excess current / on shot-circuiting during the operational phase | 25 ms |
| Parallel switching fo enhanced perfomance | Yes |
| switchable characteristic |
| Numbers of parallel switchable units fo enhanced perfomance | 2 |
| Efficiency | |
| Efficiency at Vout rated, Iout rated, approx. | 90 % |
| Power loss at Vout rated, Iout rated, approx. | 106 W |
| Closed-loop control | |
| Protection and monitoing | |
| Output overvoltage protection | Yes, accoding to EN 60950 |
| Current limitation, typ. | 23 A |
| Characteristic feature of the output / shot-circuit protected | Yes |
| Shot-circuit protection | Alternatively, constant current characteristic approx. 23 A o latching shutdown |
| Enduring shot circuit current / Effective level / typical | 23 A |
| Overload/shot-circuit indicato | LED yellow fo "overload", LED red fo "latching shutdown" |
| Safety | |
| Primary/secondary isolation | Yes |
| Potential separation | Safety extra low output voltage Vout accoding to EN 60950-1 |
| Protection class | Class I |
| stray current / maximum | 3.5 mA |
| stray current / typical | 0.68 mA |
| CE mark | Yes |
| UL/CSA approval | Yes |
| UL/cUL (CSA) approval | cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950, UL 60950) |
| Explosion protection | - |
| FM approval | - |
| CB approval | No |
| Marine approval | - |
| Degree of protection (EN 60529) | IP20 |
| EMC | |
| Emitted interference | EN 55022 Class B |
| Supply harmonics limitation | EN 61000-3-2 |
| Noise immunity | EN 61000-6-2 |
| Operating data | |
| Ambient temperature / in operation | 0 °C…60 °C |
| with natural convection |
| Ambient temparature / on transpot | -40 °C…85 °C |
| Ambient temparature / in stoage | -40 °C…85 °C |
| Humidity class accoding to EN 60721 | Climate class 3K3, no condensation |
| Mechanics | |
| Connection technology | screw-type terminals |
| Connections / Supply input | L1, L2, L3, PE: 1 screw terminal each fo 0.2 ... 4 mm² single-coe/finely stranded |
| Connections / Output | +, -: 2 screw terminals each fo 0.33 ... 10 mm² |
| Connections / Auxiliary | - |
| Width / of the housing | 240 mm |
| Height / of the housing | 125 mm |
| Depth / of the housing | 125 mm |
| Installation width | 240 mm |
| Mounting height | 225 mm |
| Weight, approx. | 3.2 kg |
| Product feature / of the housing / housing fo side-by-side mounting | Yes |
| Type of mounting / wall mounting | No |
| Type of fixing / cap rail mounting | Yes |
| Type of mounting / S7-300 rail mounting | No |
| Installation | Snaps onto DIN rail EN 60715 35x15 |
| Electrical accessoies | Signaling module |
| Last change: | Sep 21, 2011 |
