| SIPLUS ET200S EM 2AO I STANDARD -25 ... +70 DGR C WITH CONFORMAL COATING BASED ON 6ES7135-4GB01-0AB0 . +/-20MA; 13 BIT + VZ, 4 . .20MA; 13 BIT CYCLE TIME < 1MS WITH LED GF (GROUP FAULT) |
| Supply voltage |
| Load voltage L+ |
| Rated value (DC) | 24 V; From power module |
| Reverse polarity protection | Yes |
| Input current |
| from load voltage L+ (without load), max. | 150 mA |
| from backplane bus 3.3 V DC, max. | 10 mA |
| Power losses |
| Power loss, max. | 2 W |
| Address area |
| Address space per module |
| Address space per module, max. | 4 byte |
| Analog outputs |
| Number of analog outputs | 2 |
| Current output, no-load voltage, max. | 18 V |
| Cycle time (all channels) max. | 1.5 ms |
| Output ranges, current |
| -20 to +20 mA | Yes |
| 4 to 20 mA | Yes |
| Connection of actuators |
| for current output 2-conductor connection | Yes |
| for current output 4-conductor connection | No |
| Load impedance (in rated range of output) |
| with current outputs, max. | 500 Ω |
| with current outputs, inductive load, max. | 1 mH |
| Destruction limits against externally applied voltages and currents |
| Voltages at the outputs towards MANA | 15 V; max. 15 V continuous; 75 V for max. 1 s (mark to space ratio 1:20) |
| Current, max. | 50 mA; DC |
| [nicht versorgt: TAK_ABT299_001_000] |
| Cable length, shielded, max. | 200 m |
| Analog value creation |
| Integrations and conversion time/ resolution per channel |
| Resolution with overrange (bit including sign), max. | 14 bit; 4 to 20 mA: 13 bits, +/-20 mA: 14 bits |
| Settling time |
| for resistive load | 0.1 ms |
| for capacitive load | 0.5 ms |
| for inductive load | 0.5 ms |
| Errors/accuracies |
| Output ripple (based on output area, bandwidth 0 to 50 kHz) | +/- 0,02 % |
| Linearity error (relative to output area) | +/- 0,02 % |
| Temperature error (relative to output area) | +/- 0,01 %/K |
| Repeat accuracy in settled status at 25 °C (relative to output area) | +/- 0,05 % |
| Operational limit in overall temperature range |
| Current, relative to output area | +/- 0,5 % |
| Basic error limit (operational limit at 25 °C) |
| Current, relative to output area | +/- 0,3 % |
| Interrupts/diagnostics/status information |
| Substitute values connectable | Yes; 0 to 65535 (range of values must be within the rated range) |
| Diagnoses |
| Wire break | Yes |
| Group error | Yes |
| Diagnostics indication LED |
| Group error SF (red) | Yes |
| Parameter |
| Remark | 7 bytes |
| Output type/range | deactivated / +/-20 mA / 4 to 20 mA |
| Diagnosis: wire break | Disable / enable |
| Group diagnostics | Disable / enable |
| Behavior on CPU/Master STOP | Output current and de-energized/substitute a value/keep last value |
| Ex(i) characteristics |
| Max. values of output circuits (per channel) |
| Uo (output no-load voltage), max. | 18 V |
| Galvanic isolation |
| Galvanic isolation analog outputs |
| between the channels | No |
| between the channels and the backplane bus | Yes |
| between the channels and the load voltage L+ | Yes |
| Permissible potential difference |
| between MANA and M internally (UISO) | 75 VDC / 60 VAC |
| Ambient conditions |
| Extended ambient conditions |
| Relative humidity |
| with condensation / maximum | 100 % |
| Resistance |
| to biologically active substances / conformity with EN 60721-3-3 | Yes |
| to chemically active substances / conformity with EN 60721-3-3 | Yes |
| to mechanically active substances / conformity with EN 60721-3-3 | Yes |
| Dimensions |
| Width | 15 mm |
| Height | 81 mm |
| Depth | 52 mm |
| Weight |
| Weight, approx. | 40 g |
