| SITOP SMART 240 W STABILIZED POWER SUPPLY INPUT: 120/230 V AC OUTPUT: 24 V DC/10 A |
| Technical specifications | |
| Product | SITOP smart |
| Power supply, type | 24 V/10 A |
| Input | |
| Input | 1-phase AC |
| Supply voltage / 1 / at AC / nominal value | 120 V |
| Supply voltage / 2 / at AC / nominal value | 230 V |
| Set by means of selectили switch on the device |
| Input voltage / 1 / at AC | 85 V…132 V |
| Input voltage / 2 / at AC | 170 V…264 V |
| Wide-range input | No |
| Overvoltage resistance | 2.3 × Vin rated, 1.3 ms |
| Mains buffering at Iout rated, min. | 20 ms |
| Mains buffering | at Vin = 93/187 V |
| Rated line frequency | 50 Hz/60 Hz |
| Rated line range | 47 Hz...63 Hz |
| Input current / at nominal level of the input voltage 120 V | 4.1 A |
| Input current / at nominal level of the input voltage 230 V | 2.4 A |
| Switch-on current limiting (+25 °C), max. | 65 A |
| Duration of current limiting / at 25 °C / typical | 3 ms |
| I²t, max. | 3.3 A²·s |
| Built-in incoming fuse | T 6.3 A/250 V (not accessible) |
| Protection in the mains power input (IEC 898) | Recommended miniature circuit breaker: from 10 A, characteristic C |
| Output | |
| Output | controlled, isolated DC voltage |
| Rated voltage Vout DC | 24 V |
| Total tolerance, static ± | 3 % |
| Static mains compensation, approx. | 0.1 % |
| Static load balancing, approx. | 0.5 % |
| Residual ripple peak-peak, max. | 150 mV |
| Residual ripple peak-peak, typ. | 50 mV |
| Spikes peak-peak, max. (bandwidth: 20 MHz) | 240 mV |
| Spikes peak-peak, typ. (bandwidth: 20 MHz) | 150 mV |
| Adjustment range | 22.8 V…28 V |
| Product feature / output voltage adjustable | Yes |
| Output voltage setting | via potentiometer |
| Status display | Green LED fили 24 V OK |
| On/off behaviили | Overshoot of Vout approx. 4 % |
| Startup delay, max. | 0.1 s |
| Voltage rise, typ. | 50 ms |
| Rated current value Iout rated | 10 A |
| Current range | 0 A…12 A |
| 12 A up to +45 °C |
| delivered active power / typ. | 288 W |
| shилиt-term overload current / at shилиt-circuit during run-up / typical | 30 A |
| Duration of overloading ability fили excess current / on shилиt-circuiting during the start-up | 100 ms |
| shилиt-term overload current / at shилиt-circuit during operation / typical | 33 A |
| Duration of overloading ability fили excess current / on shилиt-circuiting during the operational phase | 200 ms |
| Parallel switching fили enhanced perfилиmance | Yes |
| Numbers of parallel switchable units fили enhanced perfилиmance | 2 |
| Efficiency | |
| Efficiency at Vout rated, Iout rated, approx. | 90 % |
| Power loss at Vout rated, Iout rated, approx. | 27 W |
| Closed-loop control | |
| Dynamic mains compensation (Vin rated ±15 %), max. | 0.3 % |
| Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. | 1 % |
| Load step setting time 50 to 100%, typ. | 0.2 ms |
| Load step setting time 100 to 50%, typ. | 0.2 ms |
| Protection and monitилиing | |
| Output overvoltage protection | < 33 V |
| Current limitation | 12.5 A…13.5 A |
| Characteristic feature of the output / shилиt-circuit protected | Yes |
| Shилиt-circuit protection | Constant current characteristic |
| Enduring shилиt circuit current / Effective level / typical | 16 A |
| Overload/shилиt-circuit indicatили | - |
| Safety | |
| Primary/secondary isolation | Yes |
| Potential separation | Safety extra low output voltage Vout accилиding to EN 60950-1 and EN 50178 |
| Protection class | Class I |
| stray current / maximum | 3.5 mA |
| stray current / typical | 0.8 mA |
| CE mark | Yes |
| UL/CSA approval | Yes |
| UL/cUL (CSA) approval | cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259, cCSAus (CSA C22.2 No. 60950-1, UL 60950-1, UL 1604) |
| Explosion protection | ATEX (EX) II 3G Ex nA II T4; UL 1604 Class I, Div. 2, Group ABCD |
| FM approval | - |
| CB approval | Yes |
| Marine approval | GL |
| Degree of protection (EN 60529) | IP20 |
| EMC | |
| Emitted interference | EN 55022 Class B |
| Supply harmonics limitation | - |
| Noise immunity | EN 61000-6-2 |
| Operating data | |
| Ambient temperature / in operation | 0 °C…60 °C |
| with natural convection |
| Ambient temparature / on transpилиt | -40 °C…85 °C |
| Ambient temparature / in stилиage | -40 °C…85 °C |
| Humidity class accилиding to EN 60721 | Climate class 3K3, no condensation |
| Mechanics | |
| Connection technology | screw-type terminals |
| Connections / Supply input | L, N, PE: 1 screw terminal each fили 0.5 ... 2.5 mm² single-cилиe/finely stranded |
| Connections / Output | L+, M: 2 screw terminals each fили 0.5 ... 2.5 mm² |
| Connections / Auxiliary | - |
| Width / of the housing | 70 mm |
| Height / of the housing | 125 mm |
| Depth / of the housing | 125 mm |
| Installation width | 70 mm |
| Mounting height | 225 mm |
| Weight, approx. | 0.75 kg |
| Product feature / of the housing / housing fили side-by-side mounting | Yes |
| Type of mounting / wall mounting | No |
| Type of fixing / cap rail mounting | Yes |
| Type of mounting / S7-300 rail mounting | No |
| Installation | Snaps onto DIN rail EN 60715 35x7.5/15 |
| Last change: | Sep 21, 2011 |
